How to Build a Remote-Controlled Car with a MacPherson Strut Suspension
There's a particular kind of satisfaction that comes from watching a small vehicle you built yourself glide across the garage floor, its suspension absorbing every bump with the same mechanical grace you'd find under a full-size sedan. When I decided to build an RC car with a genuine MacPherson strut suspension, I knew the chassis and geometry would be the easy part. The real challenge—and the real magic—would come from the micro servo motors that translate electrical signals into precise mechanical motion.
This article walks through the entire build, from choosing the right micro servo motors to tuning the suspension geometry so your car actually handles well. Whether you're a seasoned maker or someone who's just tired of watching RC cars bounce around like shopping carts, there's something here for you.
Why MacPherson Struts on an RC Car?
Full-scale cars have used MacPherson struts for decades because they're compact, lightweight, and cheap to manufacture. The design combines a shock absorber and a coil spring into a single unit, with the strut itself acting as the upper pivot point for the steering knuckle. On an RC car, this translates to a suspension that handles camber changes more gracefully than a simple double-wishbone setup and takes up far less space.
The trade-off is complexity. A MacPherson strut needs a properly angled upper mount, a lower control arm that swings through a specific arc, and—critically—a steering mechanism that doesn't fight the strut's motion. That last part is where micro servo motors earn their keep.
Understanding the Micro Servo Motor's Role
Before we bolt anything together, let's talk about the star of this build. A micro servo motor is a tiny package—typically 20 to 30 millimeters on a side and weighing under 20 grams—that contains a DC motor, a gear train, a potentiometer for position feedback, and a control circuit. You send it a PWM signal, and it rotates its output shaft to a corresponding angle, usually somewhere between 0 and 180 degrees.
What Makes Micro Servos Ideal for RC Suspension Work
Standard servos are bulky and heavy. On a 1/10-scale car with a MacPherson strut layout, you don't have room to waste. Micro servos fit into tight spaces between the strut tower and the chassis rail, and their low mass keeps the unsprung weight down—a critical factor when you're trying to make a small car handle predictably.
The torque figures on modern micro servos are genuinely impressive. A good unit like the SG90 or its metal-gear cousins can deliver 1.5 to 2.5 kg-cm of torque, which is more than enough to steer a lightweight RC car or actuate a suspension adjustment mechanism. Metal gears are worth the extra few dollars; plastic gears strip under the vibration and shock loads that come with actual driving.
Speed, Precision, and the PWM Signal
Micro servos typically respond to a 50 Hz PWM signal with pulse widths between 500 and 2500 microseconds. The difference between a cheap servo and a good one shows up in how precisely it holds a commanded position and how quickly it gets there. For steering, you want something in the 0.1 to 0.15 second per 60-degree range. For suspension actuation—say, adjusting ride height or damping on the fly—you can afford to go slower.
One thing I learned the hard way: micro servos don't like being back-driven. If your suspension geometry forces the servo to fight the strut's motion, you'll burn out the motor or strip gears in short order. Design your linkage so the servo only ever pushes against a load it can handle.
Chassis and Suspension Geometry
The chassis starts as a simple flat plate—I used 3mm carbon fiber, but aluminum or even stiff plywood works for a first prototype. The key dimensions come from the strut geometry. A MacPherson strut needs a lower control arm roughly equal in length to the distance from the strut's lower pivot to its upper mount, projected onto the horizontal plane. Get this wrong and you'll have a car that either won't steer or scrubs its tires off in ten minutes.
Building the Strut Towers
Each strut tower is a small upright bracket that holds the top of the strut in a compliant mount. I 3D-printed mine in PETG with a rubber grommet pressed into the top to allow a few degrees of articulation. The strut itself is a small coil-over unit—an M3 threaded rod with a pen spring and a short length of silicone tubing acting as the damper. It's crude, but it works, and it keeps the whole assembly under 15 grams per corner.
The Lower Control Arm and Knuckle
The lower control arm pivots on the chassis and connects to the steering knuckle via a ball joint—I used a small M2 ball link designed for model helicopters. The knuckle carries the wheel axle and provides a mounting point for the steering linkage. This is where the micro servo comes in: it mounts to the chassis and pushes a tie rod that connects to the knuckle's steering arm.
The critical detail is the tie rod's angle. It should be roughly parallel to the lower control arm so that suspension travel doesn't induce bump steer. On a car this small, a few degrees of misalignment translates to noticeable wandering on uneven surfaces.
Steering with a Micro Servo
I mounted a single micro servo centrally on the chassis, driving both front wheels through a pair of tie rods. A servo saver—a small spring-loaded arm—protects the gears from impacts. Without one, a hard hit against a curb will strip the servo's output gear before you can say "replaceable parts."
Programming the Steering Curve
If you're using an Arduino or similar microcontroller, you can shape the steering response in software. I mapped my transmitter's steering channel to a curve that reduces sensitivity near center and increases it toward the endpoints. This makes the car feel planted during small corrections while still allowing tight turns. The micro servo's built-in potentiometer provides the feedback loop, so the response is consistent regardless of load.
Dual Servo Setup for Four-Wheel Steering
For a more advanced build, you can add a second micro servo at the rear to steer the back wheels. A rear-steer setup with a MacPherson strut suspension is tricky because the strut's upper mount constrains the knuckle's motion, but it's doable with a revised rear geometry that uses a trailing arm instead of a lower control arm. The payoff is a turning radius that borders on ridiculous—and a car that can crab-walk sideways into tight parking spots.
Actuating Suspension Adjustments On the Fly
Here's where micro servos really shine. Instead of a fixed suspension setup, you can use micro servos to adjust ride height, damping, or even camber while driving.
Variable Ride Height
I mounted a micro servo at each strut tower with a small cam mechanism that compresses or releases the spring perch. Raising the perch stiffens the effective spring rate and increases ride height; lowering it does the opposite. With four servos and a bit of mixing in the transmitter, you can drop the car for high-speed runs and raise it for rough terrain. The servos need to be strong enough to overcome spring preload—mine are rated at 2.2 kg-cm and handle the load fine with a 3:1 reduction through the cam.
Active Damping Control
A more ambitious project involves using micro servos to rotate a small valve inside the damper, changing the effective orifice size and therefore the damping rate. I haven't perfected this yet—the seals are finicky at this scale—but the concept works in bench testing. A micro servo with a metal gear train and a tight deadband can hold a valve position accurately enough to feel the difference between soft and firm damping on a bumpy surface.
Electronics and Control
The brain of the car is an ESP32 dev board, which gives you Wi-Fi control and plenty of PWM channels. I used the Arduino framework with the ESP32Servo library, which handles the timing for up to 16 servos without jitter. The receiver is built into the ESP32—I just connect my phone or a laptop to the car's Wi-Fi access point and drive it through a web interface.
Power Budgeting
Micro servos are thirsty little things. Each one can draw half an amp or more under load, and if you're running six of them, that's a serious current spike. I power the servos from a separate 5V, 5A UBEC rather than the ESP32's onboard regulator. The motor gets its own battery, and a common ground ties everything together. Without this separation, steering inputs cause the microcontroller to brown out and reboot—which is exactly as entertaining as it sounds.
Signal Routing and Noise
Servo PWM signals are susceptible to noise from the drive motor, especially when the motor is drawing high current. I twisted each servo's signal wire with a ground wire and kept the runs short. Ferrite beads on the motor leads helped too. If your servos twitch when you apply throttle, this is the fix.
Testing and Tuning
The first drive is always humbling. My car pulled to the left, bounced over every pebble, and steered like a shopping cart with a bent wheel. Here's the sequence I used to sort it out.
Static Alignment
Set ride height first, then camber, then toe. On a MacPherson strut, camber changes as the suspension compresses, so set it at your typical ride height. I aimed for zero camber in the rear and about one degree negative in the front. Toe was a millimeter out per side, which made the car track straight without darting.
Servo Centering and Endpoint Adjustment
Center the steering servo mechanically before you touch the transmitter. Then set endpoints so the knuckles don't bind against the strut at full lock. Binding here will cook a micro servo faster than anything else.
Damping and Spring Rate
With pen springs, you don't get much choice in spring rate, but you can change the damper fluid—I used silicone oil in varying weights—and the preload. Start soft and work stiffer until the car stops bouncing after a bump. The micro servos that adjust preload make this tuning process much faster; you can change ride height from your transmitter and feel the difference immediately.
Lessons Learned and What I'd Do Differently
The biggest surprise was how much the micro servos changed the driving experience. A car with fixed suspension is a toy; a car with servo-actuated suspension is a platform. Being able to stiffen the rear on a whim, or drop the ride height for a speed run, turns every drive into an experiment.
If I built another one, I'd use metal-gear servos from the start—I went through three plastic-gear units before wising up. I'd also design the strut towers with slotted mounts so I could adjust camber without reprinting parts. And I'd add current sensing to each servo so I could detect binding before it destroys a gear train.
The MacPherson strut is a fussy geometry to scale down, but it rewards patience. Combined with micro servo motors that are small enough to hide inside the chassis and strong enough to do real work, it makes for an RC car that feels less like a toy and more like a tiny engineering project you can drive.
Copyright Statement:
Author: Micro Servo Motor
Link: https://microservomotor.com/building-remote-controlled-cars/rc-car-macpherson-strut-suspension.htm
Source: Micro Servo Motor
The copyright of this article belongs to the author. Reproduction is not allowed without permission.
Recommended Blog
- How to Build a Remote-Controlled Car with Independent Suspension
- Understanding the Basics of RC Car Charging Systems
- How to Build a Remote-Controlled Car with Autonomous Driving Capabilities
- How to Build a Remote-Controlled Car with a Single Motor System
- Essential Tools and Materials for Building an RC Car
- How to Build a Remote-Controlled Car with GPS Navigation
- How to Program an Arduino to Control Your RC Car
- How to Build a Remote-Controlled Car with LED Lights
- How to Build a Remote-Controlled Car with Working Headlights
- Exploring the Use of LiPo Batteries in RC Cars
About Us
- Lucas Bennett
- Welcome to my blog!
Hot Blog
- Troubleshooting and Fixing RC Car Receiver Power Issues
- How to Power Servo Motors with Raspberry Pi Safely
- Micro Servo Motors for Pan-Tilt Camera Gimbals on Robots
- How to Build a Remote-Controlled Car with Autonomous Driving Capabilities
- Micro Servo Motors for VTOL Drone Control Surfaces
- Smart Pet Door Controlled by Micro Servo Motors
- Mass (Weight) Effects on Performance and Specification Interpretation
- Weight Distribution and Center of Gravity Effects with Micro Servos in RC Airplanes
- Understanding the Basics of RC Car Charging Systems
- The Importance of Insulation Materials in High-Temperature Motors
Latest Blog
- How to Build a Remote-Controlled Car with a MacPherson Strut Suspension
- Using a Leap Motion Controller to Control Your Micro Servo Robotic Arm
- How to Choose the Right Cooling Method for Your Motor
- How to Maintain and Upgrade Your RC Car's Shock Springs
- The Role of Micro Servo Motors in the Development of Smart Industrial Automation
- Micro Servo Motor Price Comparison: Which Offers the Best Value?
- The Role of PWM in Signal Reconstruction
- The Role of Thermal Management in Motor Sustainability
- The Use of PWM in Signal Demodulation
- How to Control Servo Motors Using Raspberry Pi and the pigpio Library for Precision Robotics
- Using a Pressure Sensor to Control Your Micro Servo Robotic Arm
- PWM in Audio Amplifiers: Applications and Benefits
- The Role of Micro Servo Motors in Smart Scientific Systems
- How to Use Thermal Imaging for Motor Diagnostics
- Troubleshooting and Fixing RC Car Steering Sensitivity Problems
- Best Micro Servo Motors for DIY Electronics Projects
- How to Build a Remote-Controlled Car with Independent Suspension
- Using Arduino to Control the Angle of a Micro Servo Motor
- Micro Servos for Low Voltage Drones (3.7V or less)
- Micro Servo Motors in Automated Assembly Lines